Skip Navigation

How to Test a TP Sensor with a Multimeter

The throttle position sensor is an important component that feeds data to your engine control unit, regardless of how open the gas pedal or brakes are. It should be checked regularly so as not to cause any malfunctions in airflow and because it can also malfunction if neglected for too long. In this Blog Post we will Discuss How to test a TP Sensor with a Multimeter.

In general, there are four easy steps on how to test a TPS sensor with a multimeter:

●    Step 1: Examine for carbon buildup

●    Step 2: Connect TPS to Ground Wire

●    Step 3: Connect TPS to Reference Voltage

●    Step 4: Check TPS Generating Proper Signal Voltage

Curious about what I just showed you? Well, let’s take a look at how this works. 

Let me walk through the process step-by-step: 

Easy Steps to Test Your TPS with Multimeter

There are several ways to test for a throttle position sensor failure. The most common one is with an ohm meter, which will show you data at different settings, including closed and fully open valves as well as slightly opened ones in between those two extremes so that there’s room left over on your testing spectrum when it comes down just checking out specific values instead of simply noting “Ohms.”

The following are the steps on how to test a TPS sensor with a multimeter:

Step 1: Examine for Carbon Build-up

To clean the throttle plate, remove any obstruction inside your car by opening its hood. Make sure there are no impurities on this part before you start cleaning! Once everything looks fresh, use carburetor cleaner or some rags to wipe it down until they’re all sparkling clear.”

Step 2: Throttle Position Sensor Connected to Ground Wire

Inspecting your TPS for dirt, dust, or contaminants can help ensure you get the best out of it. First off, disconnect all connections from what they are connected to, and then carefully wipe away any sign of grease before setting up an inspection station with some digital multimeter (DMM) readings at roughly 20 volts, just like we did earlier today in class.
Connect the remaining lead to the positive battery portion.

The terminals should read 1 volt when you execute the throttle position sensor test. If they don’t, there may be an issue with your wiring system that will need to be resolved immediately so it doesn’t disrupt vehicle function.

Step 3: TPS is Connected to the Reference Voltage

If your TPS sensor is linked to the reference voltage rather than the ground, you must perform alternative procedures when performing this test.
The connection of the black lead to the ground will allow for an easier way to measure voltage from this point on.
Next, turn the ignition to “ON” without starting up.
After completing this step, link the red test lead-up with all three terminals. The throttle position sensor should read 5 volts at one or both of these inputs, indicating that it’s working properly and not broken like in our last experiment.

Step 4: TPS Generating the Proper Signal Voltage

To ensure that your TPS sensor test was successful and provided the right voltage, you must back probe its connector’s signal wire with a red multimeter lead multimeter. Then connect black test leads to each other while holding them near either side (or front) where they meet to define whether there is electricity flowing through these connections or not.
To start your car, make sure the key is in position and turn it to “on.” The digital multimeter should show between .2 volts and 1 volt when checking for voltage at either end of the throttle cable; if not reading this low, replace these sensors.

How to Test a TP Sensor with a Multimeter

Symptoms of a Faulty TPS

Acceleration Problems: Sometimes, the engine will not start when you accelerate. This can be caused by a problem with your car’s fuel system or wiring harnesses that prevent its proper operation and allow it to power up only enough for acceleration purposes; however, they lack sufficient strength needed at high speeds where more powerful components take over the responsibility of providing extra force on demand-which means if something were ever wrong within these vital parts (as indicated above) then all bets might as well blown because there would never any chance whatsoever getting out alive.

Unstable Engine Idling: If you notice your car going bad, idling rough, or stalling while driving, it’s time to check that sensor out.

The engine may be unstable and cause other problems like poor fuel consumption, which would worsen the situation.

Unusual Gasoline Consumption: When the sensors fail, other modules may begin to compensate for their absence by increasing fuel consumption. You will notice that your car consumes more gas than usual, which could increase by $20-$50 per month on average.

Warning Lights: The check engine light warns that your car’s sensors may not work properly. It can also mean there’s an issue with one or more important systems, like fuel mapping and monitoring pressure regulator performance: Your engine will run more inefficiently when this happens, so it pays off to take care of these problems before they get worse.

Ch Ashraf
With over 25 years of electrical contracting experience in the Gilawala area, Ashraf Electric provides reliable and efficient residential, commercial, and light industrial electrical services. As a locally owned company based in Lodhran, we specialize in quickly diagnosing and resolving electrical issues both big and small. Our team of highly skilled electricians is available 24/7 to ensure your electrical systems continue running safely. Whether you require a full rewiring, socket and switch upgrades, safety inspections, or lightning protection systems, contact Ashraf Electric for exceptional customer service and quality electrical workmanship.